teid

VoLTE: Understanding of GTP TEID to use in LTE trouble shooting

The GTP(GPRS Tunneling Protocol) is a communication protocol used by the LTE to deliver IP packets within the EPC. The GTP-C is used to deliver the controlling signals over S11 and S5, whereas the GTP-U is used to deliver application payload over S1 and S5. 


I. TEID exchanges
The TEID(Tunnel Endpoint IDentifier) is generated by each node during the initial attach procedure. The Create Session Request includes the S11 MME DL TEID and the S5 SGW DL TEID, which are generated and included by MME and Serving GW respectively. The Create Session Response includes the S5 PGW UL TEID and the S11 SGW UL TEID, which are generated and included by PGW and Serving GW respectively.

The following diagram shows the actual call flow and depicts how the TEID is exchanged between NEs. Upon receiving the Create Session Request, the Serving GW establishes the downlink GTP-C tunnel towards the MME using the received S11 MME DL TEID. In the same way the MME establishes the uplink GTP-C tunnel towards the Serving GW using the received S11 SGW UL TEID. The TEID for GTP-U is included in the body of bearer related messages (e.g., Create Bearer Request/Response, Modify Bearer Request/Response). 



The newly generated TEID is included in the body of each sending message and delivered to the peer node. The peer node perceives the end point of the GTP based on the received TEID. When the message goes through the existing GTP tunnel, the TEID of the peer node will be included in the GTP header of the sending message. The following example shows the TEID included in the Create Session Request being sent from the MME towards the Serving GW. 


In the mean time, the following example shows the TEID included in Create Session Response, where the TEID received from the MME is used in the header and the newly generated TEID of Serving GW is included in the body.



II. TEID lifetime

The life time of the GTP-C session lasts along with the life time of the UE's IP-CAN connection. It starts when the UE attaches to network and ends when the UE detaches from the network. In case there are multiple PDNs , there is only one GTP-C session per UE. The following example shows the lifetime of the same GTP-C session, which is defined by same TEIDs. In this example, there are two Create Session Requests, each for different PDNs. Each Create Session Response is followed by the Modify Bearer Request for establishing default EPS bearers. Lastly, the Create Bearer Request is to establish dedicated EPS bearers.

The lifetime of the GTP-U depends on the attributes of the EPS bearer. The GTP-U connection associated with the default EPS bearer has the same lifetime of that of GTP-C connection, whereas the GTP-U connection associated with the dedicated EPS bearer will be dynamically created and deleted within the lifetime of IP-CAN connection.

III. TEID usage

When there are multiple EPS bearers established for the same APN and there needs to verify if  specific service data flow goes through the right EPS bearer, the TEID can be a useful tool to figure it out. The following example shows the GTP-U packet of the SIP REGISTER being sent from the UE towards the IMS Core. The TEID in the GTP header indicates "0x005b8422".


The following shows the same TEID appears in the body of a Modify Bearer Request. This Modify Bearer Request is for the EPS bearer of QCI=5.




Red Mouse   http://hongjoo71-e.blogspot.com/2015/06/volte-gtp-teid_17.html

Comments

  1. josue198s22 August 2021 at 14:29

    Hello, is it possible to send me the .pcap or post it on your blog so I can download it?

    ReplyDelete

Post a Comment

Popular posts from this blog

LTE : Tracking Area Update with SGW Change

LTE : Tracking Area Update with SGW Change After an hour of Metallica rock and few shots of Espresso I sat down on the saturday afternoon to understand the another handover scenario in LTE. Some time back I wrote about  Tracking Area Update Procedure without SGW change . In this post I would like to explore Tracking Area Update procedure  WITH  SGW change. Ref : 3GPP TS 23.401 5.3.3.1. Before we dive into the post a quick note. Tracking Area is the area/cell being tracked by an eNB. TAI change may indicate a change in eNB. Routing Area is the area/cells tracked by a SGW. So a SGW can track multiple tracking areas. The title of the post is little confusing. I say Tracking area update with SGW change and also say tracking area is taken care by eNB. Well if a eNB changes and the corresponding MME changes which may also lead to a SGW change. This is the scenario we are dealing below. The below picture should be of some help. When UE detects that it has entered a new Cell then it
Read more

TEID 2

Image
Bearer Building and Tunnel Timing from ; http://lteuniversity.com/get_trained/expert_opinion1/b/donhanley/archive/2012/01/30/bearer-building-and-tunnel-timing.aspx By now, you should be familiar with the concept of an EPS bearer, which transports user traffic between the User Equipment (UE) and the PDN Gateway (P-GW) in LTE networks. If you’ve taken just about any Award Solutions course on LTE, you’ve learned that an EPS bearer is comprised of 3 parts: the Data Radio Bearer (DRB) over the air interface between the UE and the evolved Node B (eNB); the S1-U bearer between the eNB and the Serving Gateway (S-GW); and the S5 bearer between the S-GW and the P-GW. You will also recall that the S1-U and S5 bearers make use of GPRS Tunneling Protocol (GTP) to identify the individual bearers connecting two nodes. Since each eNB, S-GW and P-GW may be supporting hundreds of active bearers, the GTP Tunnel Endpoint Identifiers (TEIDs) assigned to each bearer allows each node to determine
Read more